- Detection threshold, AC only or AC/DC
- Body length, clip, and battery type
- Lead or probe scope if any
- Safety category on the pen and the tip
- Quantity, destination, Incoterm
PEN QUOTATION SCOPE
Voltage tester pen price
A voltage tester pen price is a quotation problem, not a shelf sticker. LinkScope Sourcing 59 collects the pen configuration and asks factories to answer the same detection threshold, tip, battery, and freight lines. The desk is an independent sourcing partner. It does not stock pens and it does not certify a non-contact indication as a measured voltage.
Evidence ledger for a pen quotation
Each row is a question the proposed supplier must answer for the exact model. IEEE Ethernet overviews and other network standards do not describe pen behavior. They are not a substitute for the pen datasheet.
| Line | What to request | Why the price moves |
|---|---|---|
| Measurement function | Non-contact field indication, contact tip, or both in one body | A dual-function pen is a different bill of material |
| Threshold | Published AC detection point, for example near 90 V AC, and whether DC is ignored | A 50 V site and a 90 V threshold can miss the task |
| Impedance | State high-impedance tip versus any low-impedance contact mode | Ghost voltage handling is not included by default |
| Frequency range | 50 Hz and 60 Hz behavior, plus any stated upper limit | A pen tuned for mains can be silent on other waveforms |
| Safety category | IEC 61010-1 category marked on the pen, such as CAT III 1000 V or CAT IV 600 V | The marking limits where a crew may use it |
| Ingress protection | IP rating if the pen is used in pedestals or outdoor huts | An unstated enclosure is an open exclusion |
| Calibration evidence | Whether the pen is go/no-go or shows a number that needs measurement accuracy | A numeric display pulls in calibration traceability |
Background: a central-office crew wanted pocket pens before opening rectifier cabinets. Process: the brief split non-contact indication from a separate contact check on the -48 V DC bus, because the pen datasheet under review listed AC detection only. Result: the voltage tester pen price was requested as a pen line, and the DC contact tester stayed on its own line so the two quotations could not be averaged into one unit price. That scenario is a procurement example, not a completed shipment and not a customer testimonial.
Accessory scope belongs in the same ledger. A pocket clip, a spare battery, and a carrying case change the delivered kit even when the pen body looks identical in a photo. Ask the factory to mark each of those as included, optional, or excluded. If the pen uses replaceable batteries, name the cell size so a later reorder does not assume a sealed pack.
Quantity units for this family are units, not ports or kilometers. A carton quantity is still a count of pens. If you need ten pens for a crew and two contact testers for the DC bus, write both counts. Destination is the US site that will receive the goods, including whether the address is a warehouse or a central office dock. Expected timing is a requested window, not a promise from this desk.
Commercial exclusions need their own sentences. Duty, brokerage, and freight can exceed the pen body on a small order. A target budget, if you have one, should say the currency and whether it is per pen or the whole order. High-end, mid-range, budget, or undecided is your preference about finish, documentation, and support. It is not a rating this desk has verified, and you do not need an existing quotation to start.
Limitations sit next to the ledger so they are not discovered after the purchase order. A non-contact pen does not report magnitude. It can light near a live conductor and also near a coupled conductor. Shielded cable, thick insulation, and distance from the conductor all change the indication. The pen does not prove a circuit is de-energized. A contact method, a rated lead set, and the site lockout procedure remain outside the pen price.
Compare the inquiry names on the tester lines page, then send the ledger through the form. The procurement brief lists the same measurement, range, and evidence fields in article form.
Pen compatibility questions
Can one pen price cover both a pedestal and a DC plant?
Only if the datasheet states both environments. An AC field pen can be the wrong tool on a -48 V DC bus. Write the installation in the brief so the factory cannot answer with a single mains pen.
Are OEM and unmarked compatible pens the same line?
No. An OEM-marked pen may align with one support route. An unmarked compatible pen may widen the factory list only after the exact threshold, category, and tip are confirmed. A shared photo is not that confirmation. This is the same kind of split buyers already face with OEM-coded versus compatible network modules: the name on the housing is not the test.
What should a refurbished pen disclose?
New versus refurbished changes battery age, tip wear, and whether the safety category print is intact. Ask for condition, any remaining calibration traceability if the pen displays a number, and the warranty route. Do not treat a lower unit price as a matched configuration.
Paste pen lines into the brief
This panel is not a file upload. There is no attachment field. Type the pen rows into the requirement box, or send drawings after the desk replies. Repeat the detection threshold, safety category, quantity, destination, and timing in that box so a factory cannot quote a different pen.
If JavaScript is off, the budget and supplier preference also belong in the same box. The form posts to the existing inquiry action used across this desk.